For a full table of possible MCS index connection rates see ġ) Select your country first and YOU MUST HIT APPLY! The driver needs to reconfigure the country for the speific wifi chipset and then the router needs to get the updated channel list for your countryģA) Select the correct WiFi "carrier" channel and concurrently go to 3B.ģB) Set the Extension Channel UU, LL, UL, or LU. Using lower MHz channel width values yields more free non-overlapping channels but means less bandwidth/throughput is available. This determines the wireless channel width used- where higher values allow more bandwidth/throughput, but yield fewer free channels, and result in more overlapping channels. N is up to 40Mhz wide bands and up to 600Mbit (4x4 MIMO)ĪC is up to 160Mhz wide bands and 1733Mbit (2x2 MIMO) in 5ghz For 802.11a/n 5 GHz radios, Mixed & NA-Mixed are the same.Ī is the worst standard with 20Mhz wide bands and 54Mbit upper limit (legacy mode) N-Only is broken on many units for some time (both bands) & still is, try to avoid using as there is minimal performance change from NG-Mixed -> N-Only if all you use is 802.11n clients for either of them. If you have any issues or do not use 802.11b clients, switch to NG-Mixed. NG-Mixed for 2.4 GHz & Mixed or AC/N-Mixed is the recommended setting for most people as your clients' NICs are able to use either (V)HT20, (V)HT40, & VHT80 "properly" with this setting. Depending on the selected network mode your wireless channel list and maximum TX power can vary. Recommended Setting: Ĭontrols which 802.11 signals are being broadcast by the radio. See this page for more info on linking routers: Linking RoutersĪvailable Settings (2.4 GHz): Disabled, Mixed, B-Only, G-Only, BG-Mixed, NG-Mixed, N-Only (2.4 GHz)Īvailable Settings (5 GHz): Disabled, Mixed, A-Only, NA-Mixed, AC/N-Mixed, N-Only (5 GHz), AC-OnlyĪvailable Settings (60 GHz): Disabled, Mixed, AD-Only Client, Client Bridge (Routed), & WDS Station is the Qualcomm Atheros equivalent to Broadcom & Mediatek's Repeater and Repeater Bridge modes. If you want to run a normal access point which most do, AP would be your choice. Recommended Setting: AP for most users, other options if you are advanced and know you need itĭetermines how the specific wireless interface of the router is to behave. Refer to this thread for some info about VAPs with Qualcomm Atheros.Īvailable Settings: AP, Client, Client Bridge (Routed), AdHoc, WDS Station, WDS AP For example, a VAP made on ath0 will be ath0.1, then ath0.2, etc. If you create a VAP for 2.4GHz or 5GHz radio the VAPs will be labelled athX.1 & athX.1 respectively where X = the interface's number. Ath0 is the 2.4GHz radio and ath1 is the 5GHz radio for most routers, for some like the TL-WDR4900 v1.3, ath0 is 5GHz & ath1 is 2.4GHz its just the way the radios are connected on the PCB & is normal. If you have a dual band router ath1 will be displayed below ath0 with the same available settings. Standard Settings Wireless Physical InterfaceĪvailable Interfaces: athX (0, 1, 2 etc, varies by router as many routers have 2 or more radios in them) Basic Wireless Settings apply to all routers, all of which are listed here under standard settings. If you are a Broadcom or Mediatek (formerly Ralink) user, please refer to Advanced wireless settings for Broadcom/Mediatek wireless settings. Not every router shows every possible setting shown here as some routers will have less. This page shows the contents and descriptions of standard and advanced wireless settings for Qualcomm Atheros (QCA) based 802.11a/b/g/n/ac/ad routers.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |